#
# /etc/sysctl.conf: configuration for system variables, see sysctl.conf(5)
#

kernel.printk = 1 4 1 7

# Disable ipv6
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
net.ipv6.conf.lo.disable_ipv6 = 1

# Tuen IPv6
# net.ipv6.conf.default.router_solicitations = 0
# net.ipv6.conf.default.accept_ra_rtr_pref = 0
# net.ipv6.conf.default.accept_ra_pinfo = 0
# net.ipv6.conf.default.accept_ra_defrtr = 0
# net.ipv6.conf.default.autoconf = 0
# net.ipv6.conf.default.dad_transmits = 0
# net.ipv6.conf.default.max_addresses = 0

# Avoid a smurf attack
net.ipv4.icmp_echo_ignore_broadcasts = 1

# Turn on protection for bad icmp error messages
net.ipv4.icmp_ignore_bogus_error_responses = 1

# Turn on syncookies for SYN flood attack protection
net.ipv4.tcp_syncookies = 1

## protect against tcp time-wait assassination hazards
## drop RST packets for sockets in the time-wait state
## (not widely supported outside of linux, but conforms to RFC)
net.ipv4.tcp_rfc1337 = 1

## tcp timestamps
## + protect against wrapping sequence numbers (at gigabit speeds)
## + round trip time calculation implemented in TCP
## - causes extra overhead and allows uptime detection by scanners like nmap
## enable @ gigabit speeds
net.ipv4.tcp_timestamps = 0
#net.ipv4.tcp_timestamps = 1

# Turn on and log spoofed, source routed, and redirect packets
net.ipv4.conf.all.log_martians = 1
net.ipv4.conf.default.log_martians = 1

## ignore echo broadcast requests to prevent being part of smurf attacks (default)
net.ipv4.icmp_echo_ignore_broadcasts = 1

# No source routed packets here
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.default.accept_source_route = 0

## sets the kernels reverse path filtering mechanism to value 1(on)
## will do source validation of the packet's recieved from all the interfaces on the machine
## protects from attackers that are using ip spoofing methods to do harm
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.default.rp_filter = 1
net.ipv6.conf.default.rp_filter = 1
net.ipv6.conf.all.rp_filter = 1

# Make sure no one can alter the routing tables
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.default.accept_redirects = 0
net.ipv4.conf.all.secure_redirects = 0
net.ipv4.conf.default.secure_redirects = 0

# Act as a router, necessary for Access Point
net.ipv4.ip_forward = 1
net.ipv4.conf.all.send_redirects = 1
net.ipv4.conf.default.send_redirects = 1

kernel.shmmax = 500000000
# Turn on execshild
kernel.exec-shield = 1
kernel.randomize_va_space = 1

# Optimization for port usefor LBs
# Increase system file descriptor limit
fs.file-max = 65535

# Allow for more PIDs (to reduce rollover problems); may break some programs 32768
kernel.pid_max = 65536

# Increase system IP port limits
net.ipv4.ip_local_port_range = 2000 65000

# Increase TCP max buffer size setable using setsockopt()
net.ipv4.tcp_rmem = 4096 87380 8388608
net.ipv4.tcp_wmem = 4096 87380 8388608

# Increase Linux auto tuning TCP buffer limits
# min, default, and max number of bytes to use
# set max to at least 4MB, or higher if you use very high BDP paths
# Tcp Windows etc
net.core.rmem_max = 8388608
net.core.wmem_max = 8388608
net.core.netdev_max_backlog = 5000
net.ipv4.tcp_window_scaling = 1

# End of file