# Mu synchronizes between routines using channels rather than locks, like
# Erlang and Go.
#
# Key properties of channels:
#
# a) Writing to a full channel or reading from an empty one will put the
# current routine in 'waiting' state until the operation can be completed.
#
# b) Writing to a channel implicitly performs a deep copy. This prevents
# addresses from being shared between routines, and therefore eliminates all
# possibility of race conditions.
#
# There's still a narrow window for race conditions: the ingredients passed in
# to 'start-running'. Pass only channels into routines and you should be fine.
# Any other mutable ingredients will require locks.
scenario channel [
run [
local-scope
source:&:source:num, sink:&:sink:num <- new-channel 3/capacity
sink <- write sink, 34
10:num/raw, 11:bool/raw, source <- read source
]
memory-should-contain [
10 <- 34
11 <- 0 # read was successful
]
]
container channel:_elem [
lock:bool # inefficient but simple: serialize all reads as well as writes
first-full:num # for write
first-free:num # for read
# A circular buffer contains values from index first-full up to (but not
# including) index first-empty. The reader always modifies it at first-full,
# while the writer always modifies it at first-empty.
data:&:@:_elem
]
# Since channels have two ends, and since it's an error to use either end from
# multiple routines, let's distinguish the ends.
container source:_elem [
chan:&:channel:_elem
]
container sink:_elem [
chan:&:channel:_elem
]
def new-channel capacity:num -> in:&:source:_elem, out:&:sink:_elem [
local-scope
load-ingredients
result:&:channel:_elem <- new {(channel _elem): type}
*result <- put *result, first-full:offset, 0
*result <- put *result, first-free:offset, 0
capacity <- add capacity, 1 # unused slot for 'full?' below
data:&:@:_elem <- new _elem:type, capacity
*result <- put *result, data:offset, data
in <- new {(source _elem): type}
*in <- put *in, chan:offset, result
out <- new {(sink _elem): type}
*out <- put *out, chan:offset, result
]
def write out:&:sink:_elem, val:_elem -> out:&:sink:_elem [
local-scope
load-ingredients
assert out, [write to null channel]
chan:&:channel:_elem <- get *out, chan:offset
<channel-write-initial>
# block until lock is acquired AND queue has room
lock:location <- get-location *chan, lock:offset
#? $print [write], 10/newline
{
#? $print [trying to acquire lock for writing], 10/newline
wait-for-reset-then-set lock
#? $print [lock acquired for writing], 10/newline
full?:bool <- channel-full? chan
break-unless full?
#? $print [but channel is full; relinquishing lock], 10/newline
# channel is full; relinquish lock and give a reader the opportunity to
# create room on it
reset lock
current-routine-is-blocked
switch # avoid spinlocking
loop
}
current-routine-is-unblocked
#? $print [performing write], 10/newline
# store a deep copy of val
circular-buffer:&:@:_elem <- get *chan, data:offset
free:num <- get *chan, first-free:offset
val-copy:_elem <- deep-copy val # on this instruction rests all Mu's concurrency-safety
*circular-buffer <- put-index *circular-buffer, free, val-copy
# mark its slot as filled
free <- add free, 1
{
# wrap free around to 0 if necessary
len:num <- length *circular-buffer
at-end?:bool <- greater-or-equal free, len
break-unless at-end?
free <- copy 0
}
# write back
*chan <- put *chan, first-free:offset, free
#? $print [relinquishing lock after writing], 10/newline
reset lock
]
def read in:&:source:_elem -> result:_elem, eof?:bool, in:&:source:_elem [
local-scope
load-ingredients
assert in, [read on null channel]
eof? <- copy 0/false # default result
chan:&:channel:_elem <- get *in, chan:offset
# block until lock is acquired AND queue has data
lock:location <- get-location *chan, lock:offset
#? $print [read], 10/newline
{
#? $print [trying to acquire lock for reading], 10/newline
wait-for-reset-then-set lock
#? $print [lock acquired for reading], 10/newline
empty?:bool <- channel-empty? chan
break-unless empty?
#? $print [but channel is empty; relinquishing lock], 10/newline
# channel is empty; relinquish lock and give a writer the opportunity to
# add to it
reset lock
current-routine-is-blocked
<channel-read-empty>
switch # avoid spinlocking
loop
}
current-routine-is-unblocked
# pull result off
full:num <- get *chan, first-full:offset
circular-buffer:&:@:_elem <- get *chan, data:offset
result <- index *circular-buffer, full
# clear the slot
empty:&:_elem <- new _elem:type
*circular-buffer <- put-index *circular-buffer, full, *empty
# mark its slot as empty
full <- add full, 1
{
# wrap full around to 0 if necessary
len:num <- length *circular-buffer
at-end?:bool <- greater-or-equal full, len
break-unless at-end?
full <- copy 0
}
# write back
*chan <- put *chan, first-full:offset, full
#? $print [relinquishing lock after reading], 10/newline
reset lock
]
def clear in:&:source:_elem -> in:&:source:_elem [
local-scope
load-ingredients
chan:&:channel:_elem <- get *in, chan:offset
{
empty?:bool <- channel-empty? chan
break-if empty?
_, _, in <- read in
}
]
scenario channel-initialization [
run [
local-scope
source:&:source:num <- new-channel 3/capacity
chan:&:channel:num <- get *source, chan:offset
10:num/raw <- get *chan, first-full:offset
11:num/raw <- get *chan, first-free:offset
]
memory-should-contain [
10 <- 0 # first-full
11 <- 0 # first-free
]
]
scenario channel-write-increments-free [
local-scope
_, sink:&:sink:num <- new-channel 3/capacity
run [
sink <- write sink, 34
chan:&:channel:num <- get *sink, chan:offset
10:num/raw <- get *chan, first-full:offset
11:num/raw <- get *chan, first-free:offset
]
memory-should-contain [
10 <- 0 # first-full
11 <- 1 # first-free
]
]
scenario channel-read-increments-full [
local-scope
source:&:source:num, sink:&:sink:num <- new-channel 3/capacity
sink <- write sink, 34
run [
_, _, source <- read source
chan:&:channel:num <- get *source, chan:offset
10:num/raw <- get *chan, first-full:offset
11:num/raw <- get *chan, first-free:offset
]
memory-should-contain [
10 <- 1 # first-full
11 <- 1 # first-free
]
]
scenario channel-wrap [
local-scope
# channel with just 1 slot
source:&:source:num, sink:&:sink:num <- new-channel 1/capacity
chan:&:channel:num <- get *source, chan:offset
# write and read a value
sink <- write sink, 34
_, _, source <- read source
run [
# first-free will now be 1
10:num/raw <- get *chan, first-free:offset
11:num/raw <- get *chan, first-free:offset
# write second value, verify that first-free wraps
sink <- write sink, 34
20:num/raw <- get *chan, first-free:offset
# read second value, verify that first-full wraps
_, _, source <- read source
30:num/raw <- get *chan, first-full:offset
]
memory-should-contain [
10 <- 1 # first-free after first write
11 <- 1 # first-full after first read
20 <- 0 # first-free after second write, wrapped
30 <- 0 # first-full after second read, wrapped
]
]
scenario channel-new-empty-not-full [
run [
local-scope
source:&:source:num <- new-channel 3/capacity
chan:&:channel:num <- get *source, chan:offset
10:bool/raw <- channel-empty? chan
11:bool/raw <- channel-full? chan
]
memory-should-contain [
10 <- 1 # empty?
11 <- 0 # full?
]
]
scenario channel-write-not-empty [
local-scope
source:&:source:num, sink:&:sink:num <- new-channel 3/capacity
chan:&:channel:num <- get *source, chan:offset
run [
sink <- write sink, 34
10:bool/raw <- channel-empty? chan
11:bool/raw <- channel-full? chan
]
memory-should-contain [
10 <- 0 # empty?
11 <- 0 # full?
]
]
scenario channel-write-full [
local-scope
source:&:source:num, sink:&:sink:num <- new-channel 1/capacity
chan:&:channel:num <- get *source, chan:offset
run [
sink <- write sink, 34
10:bool/raw <- channel-empty? chan
11:bool/raw <- channel-full? chan
]
memory-should-contain [
10 <- 0 # empty?
11 <- 1 # full?
]
]
scenario channel-read-not-full [
local-scope
source:&:source:num, sink:&:sink:num <- new-channel 1/capacity
chan:&:channel:num <- get *source, chan:offset
sink <- write sink, 34
run [
_, _, source <- read source
10:bool/raw <- channel-empty? chan
11:bool/raw <- channel-full? chan
]
memory-should-contain [
10 <- 1 # empty?
11 <- 0 # full?
]
]
## cancelling channels
# every channel comes with a boolean signifying if it's been closed
# initially this boolean is false
container channel:_elem [
closed?:bool
]
# a channel can be closed from either the source or the sink
# both routines can modify the 'closed?' bit, but they can only ever set it, so this is a benign race
def close x:&:source:_elem -> x:&:source:_elem [
local-scope
load-ingredients
chan:&:channel:_elem <- get *x, chan:offset
*chan <- put *chan, closed?:offset, 1/true
]
def close x:&:sink:_elem -> x:&:sink:_elem [
local-scope
load-ingredients
chan:&:channel:_elem <- get *x, chan:offset
*chan <- put *chan, closed?:offset, 1/true
]
# once a channel is closed from one side, no further operations are expected from that side
# if a channel is closed for reading,
# no further writes will be let through
# if a channel is closed for writing,
# future reads continue until the channel empties,
# then the channel is also closed for reading
after <channel-write-initial> [
closed?:bool <- get *chan, closed?:offset
return-if closed?
]
after <channel-read-empty> [
closed?:bool <- get *chan, closed?:offset
{
break-unless closed?
empty-result:&:_elem <- new _elem:type
current-routine-is-unblocked
return *empty-result, 1/true
}
]
## helpers
# An empty channel has first-empty and first-full both at the same value.
def channel-empty? chan:&:channel:_elem -> result:bool [
local-scope
load-ingredients
# return chan.first-full == chan.first-free
full:num <- get *chan, first-full:offset
free:num <- get *chan, first-free:offset
result <- equal full, free
]
# A full channel has first-empty just before first-full, wasting one slot.
# (Other alternatives: https://en.wikipedia.org/wiki/Circular_buffer#Full_.2F_Empty_Buffer_Distinction)
def channel-full? chan:&:channel:_elem -> result:bool [
local-scope
load-ingredients
# tmp = chan.first-free + 1
tmp:num <- get *chan, first-free:offset
tmp <- add tmp, 1
{
# if tmp == chan.capacity, tmp = 0
len:num <- capacity chan
at-end?:bool <- greater-or-equal tmp, len
break-unless at-end?
tmp <- copy 0
}
# return chan.first-full == tmp
full:num <- get *chan, first-full:offset
result <- equal full, tmp
]
def capacity chan:&:channel:_elem -> result:num [
local-scope
load-ingredients
q:&:@:_elem <- get *chan, data:offset
result <- length *q
]
## helpers for channels of characters in particular
def buffer-lines in:&:source:char, buffered-out:&:sink:char -> buffered-out:&:sink:char, in:&:source:char [
local-scope
load-ingredients
# repeat forever
eof?:bool <- copy 0/false
{
line:&:buffer <- new-buffer 30
# read characters from 'in' until newline, copy into line
{
+next-character
c:char, eof?:bool, in <- read in
break-if eof?
# drop a character on backspace
{
# special-case: if it's a backspace
backspace?:bool <- equal c, 8
break-unless backspace?
# drop previous character
{
buffer-length:num <- get *line, length:offset
buffer-empty?:bool <- equal buffer-length, 0
break-if buffer-empty?
buffer-length <- subtract buffer-length, 1
*line <- put *line, length:offset, buffer-length
}
# and don't append this one
loop +next-character
}
# append anything else
line <- append line, c
line-done?:bool <- equal c, 10/newline
break-if line-done?
loop
}
# copy line into 'buffered-out'
i:num <- copy 0
line-contents:text <- get *line, data:offset
max:num <- get *line, length:offset
{
done?:bool <- greater-or-equal i, max
break-if done?
c:char <- index *line-contents, i
buffered-out <- write buffered-out, c
i <- add i, 1
loop
}
{
break-unless eof?
buffered-out <- close buffered-out
return
}
loop
}
]
scenario buffer-lines-blocks-until-newline [
run [
local-scope
source:&:source:char, sink:&:sink:char <- new-channel 10/capacity
_, buffered-stdin:&:sink:char/buffered-stdin <- new-channel 10/capacity
buffered-chan:&:channel:char <- get *buffered-stdin, chan:offset
empty?:bool <- channel-empty? buffered-chan
assert empty?, [
F buffer-lines-blocks-until-newline: channel should be empty after init]
# buffer stdin into buffered-stdin, try to read from buffered-stdin
buffer-routine:num <- start-running buffer-lines, source, buffered-stdin
wait-for-routine-to-block buffer-routine
empty? <- channel-empty? buffered-chan
assert empty?:bool, [
F buffer-lines-blocks-until-newline: channel should be empty after buffer-lines bring-up]
# write 'a'
sink <- write sink, 97/a
restart buffer-routine
wait-for-routine-to-block buffer-routine
empty? <- channel-empty? buffered-chan
assert empty?:bool, [
F buffer-lines-blocks-until-newline: channel should be empty after writing 'a']
# write 'b'
sink <- write sink, 98/b
restart buffer-routine
wait-for-routine-to-block buffer-routine
empty? <- channel-empty? buffered-chan
assert empty?:bool, [
F buffer-lines-blocks-until-newline: channel should be empty after writing 'b']
# write newline
sink <- write sink, 10/newline
restart buffer-routine
wait-for-routine-to-block buffer-routine
empty? <- channel-empty? buffered-chan
data-emitted?:bool <- not empty?
assert data-emitted?, [
F buffer-lines-blocks-until-newline: channel should contain data after writing newline]
trace 1, [test], [reached end]
]
trace-should-contain [
test: reached end
]
]
def drain source:&:source:char -> result:text, source:&:source:char [
local-scope
load-ingredients
buf:&:buffer <- new-buffer 30
{
c:char, done?:bool <- read source
break-if done?
buf <- append buf, c
loop
}
result <- buffer-to-array buf
]